Is Category 4 PPE required for all high-voltage work? No. Arc flash PPE is chosen from an arc flash risk assessment of the specific equipment and task, not from the voltage alone. This guide explains how NFPA 70E links incident energy, the arc flash boundary and PPE categories to the clothing, face, head, hand and foot protection your crew needs.
Not sure what rating your crew needs? Talk to our team about arc flash PPE and NFPA 70E training.
Call (303) 537-5832Key takeaways
- Pick arc flash PPE from an arc flash risk assessment of the equipment, its condition and the task, not from voltage alone.
- NFPA 70E allows two methods: the incident energy analysis method or the arc flash PPE category method. Use one or the other on a given piece of equipment, not both.
- With incident energy analysis, the PPE's arc rating must be equal to or greater than the calculated incident energy.
- Category minimums are 4, 8, 25 and 40 cal/cm² for Categories 1 to 4, and each category also sets the face, head, hand, hearing and foot protection required.
- Untreated cotton is not arc flash PPE. The outer layer must be arc-rated; non-melting natural fibers are allowed only underneath.
1. Which rules require arc flash PPE
- OSHA requires employers to assess workplace hazards and provide suitable PPE (29 CFR 1910.132(d)), and to provide electrical protective equipment to employees exposed to electrical hazards (1910.335(a)). Power generation, transmission and distribution work has its own arc flash rules under 1910.269(l)(8).
- NFPA 70E, the Standard for Electrical Safety in the Workplace, explains how to assess arc flash risk and select PPE. OSHA does not adopt it by reference, but it is widely used to show compliance with OSHA's general requirements. The current edition is 2024.
Colorado private-sector employers fall under federal OSHA, so these federal rules apply directly.
2. The arc flash risk assessment
NFPA 70E requires an arc flash risk assessment before anyone works within the arc flash boundary of exposed energized equipment (NFPA 70E 130.5). It must:
- Identify arc flash hazards and estimate how likely an arc flash is and how severe it could be.
- Decide whether more protective measures, including PPE, are needed.
- Be reviewed for accuracy at least every 5 years, and whenever equipment or the electrical system changes.
Likelihood matters. Normal operation of equipment that is properly installed and maintained, with doors closed and secured and no sign of impending failure, may not present an arc flash risk. Opening covers, racking breakers, testing and troubleshooting usually do.
Arc flash boundary. This is the distance from an arc source at which incident energy equals 1.2 cal/cm² (5 J/cm²), roughly the threshold for a second-degree burn. Anyone inside it needs arc flash PPE.
Equipment labels. Equipment must be labeled with the nominal voltage, the arc flash boundary, and either the available incident energy and working distance or the PPE category (NFPA 70E 130.5(H)). If a label is missing or out of date, don't borrow numbers from similar equipment. Have that equipment assessed.
3. Incident energy analysis method
An incident energy analysis calculates the heat energy a worker could receive at a set working distance from a specific piece of equipment. It is expressed in calories per square centimeter (cal/cm²).
- Arc-rated clothing is required wherever incident energy is 1.2 cal/cm² or more.
- The arc rating of the PPE must be equal to or greater than the calculated incident energy. For example, at 3.7 cal/cm² you need PPE rated at least 3.7 cal/cm², such as a standard 8 cal/cm² arc-rated shirt and pants.
- The analysis applies only at the working distance used in the calculation. Working closer increases the exposure.
- Above 40 cal/cm², the PPE categories no longer apply. Exposure at that level calls for a detailed analysis, and de-energizing the equipment should be the first choice.
4. Arc flash PPE category method
The category method uses NFPA 70E tables instead of a calculation. It is only valid when the equipment falls within the table's limits for available fault current, fault clearing time and working distance. If the equipment is outside those limits, or the limits are unknown, an incident energy analysis is required.
| Category | Min. arc rating | Required PPE (NFPA 70E Table 130.7(C)(15)(c)) |
|---|---|---|
| 1 | 4 cal/cm² | Arc-rated long-sleeve shirt and pants or coverall; arc-rated face shield or arc flash suit hood; hard hat; safety glasses or goggles; hearing protection (ear canal inserts); heavy-duty leather gloves, arc-rated gloves, or rubber insulating gloves with leather protectors; leather footwear as needed |
| 2 | 8 cal/cm² | Arc-rated long-sleeve shirt and pants or coverall; arc-rated face shield and arc-rated balaclava, or an arc flash suit hood; hard hat; safety glasses or goggles; hearing protection; gloves as in Category 1; leather footwear |
| 3 | 25 cal/cm² | Arc-rated clothing system (shirt, pants, coverall, or arc flash suit jacket and pants) meeting 25 cal/cm²; arc flash suit hood; hard hat; safety glasses or goggles; hearing protection; arc-rated gloves or rubber insulating gloves with leather protectors; leather footwear |
| 4 | 40 cal/cm² | Same items as Category 3, rated for at least 40 cal/cm² |
Category 4 is not a default for high-voltage work. Over-protecting adds heat stress and limits movement and visibility, which creates its own hazards. Use the category the assessment calls for.
5. Head, face and hearing protection
- Face shields must be arc-rated and wrap around to protect the face, chin, forehead, ears and neck. A face shield alone is not a complete ensemble.
- Balaclavas are worn with a face shield in Category 2 to cover the head and neck.
- Arc flash suit hoods are required in Categories 3 and 4 and can replace the shield-and-balaclava combination in Categories 1 and 2. Check the hood's arc rating, lens visibility and fit with the hard hat.
- Hard hats, safety glasses or goggles, and ear canal inserts are part of every category. Arc blasts are loud enough to damage hearing.
- Inspect before each use. Remove damaged or contaminated items from service and follow the manufacturer's care instructions.
6. Clothing layers, gloves and footwear
- The outer layer must be arc-rated. Flame-resistant (FR) is not the same as arc-rated; check the label for an arc rating (ATPV or EBT) in cal/cm².
- Under layers must be arc-rated or made of non-melting natural fibers such as untreated cotton, wool or silk. Never wear meltable fabrics like polyester, nylon or spandex underneath.
- Garments must cover the body fully, with sleeves fastened and shirts tucked in, and overlap with gloves and the hood or balaclava without gaps.
- Gloves: heavy-duty leather or better in Categories 1 and 2; arc-rated gloves or rubber insulating gloves with leather protectors in Categories 3 and 4. Rubber insulating gloves also protect against shock and must be rated for the voltage.
- Footwear: leather work shoes or boots, required from Category 2 up.
- Launder and repair arc-rated clothing only as the manufacturer directs, and replace garments that are damaged or contaminated with flammable material.
Train the people who wear it
PPE only works when workers know the boundaries, read the labels and wear the full ensemble correctly. NFPA 70E requires qualified-person training, with retraining at least every 3 years.
Need arc flash PPE or NFPA 70E training?
Colorado Safety Supply Company helps Colorado employers choose arc-rated PPE and runs NFPA 70E and other safety classes in Denver.
Frequently asked questions
Is Category 4 PPE required for all high-voltage work?
No. The PPE level comes from the arc flash risk assessment of the specific equipment and task. Category 4 applies only when the category tables or an incident energy analysis call for protection of at least 40 cal/cm².
Can I wear 100% cotton as arc flash PPE?
No. Untreated cotton can ignite and is not arc flash PPE. It may be worn only as an under layer beneath arc-rated clothing, because it does not melt onto the skin.
What does cal/cm² mean?
Calories per square centimeter is the unit for incident energy and for a garment's arc rating. 1.2 cal/cm² is roughly the energy that causes a second-degree burn on bare skin, which is why it defines the arc flash boundary.
Is flame-resistant (FR) clothing the same as arc-rated clothing?
No. Arc-rated clothing is flame-resistant, but not all FR clothing has been tested for arc flash. For arc flash PPE, the garment label must show an arc rating in cal/cm².
How often does an arc flash risk assessment need updating?
NFPA 70E requires a review at least every 5 years, and sooner when equipment, the electrical system or work procedures change.
This article is general guidance based on NFPA 70E (2024 edition) and OSHA standards. It does not replace an arc flash risk assessment, equipment labels or the full text of the standards.



















